# Framing and Stud Calculator

Canonical URL: https://www.simplywise.com/blog/framing-stud-calculator/
Plain text: https://www.simplywise.com/blog/framing-stud-calculator/llms.txt
Publisher: SimplyWise, Inc. (https://www.simplywise.com)
Published: September 17, 2026
Updated: October 27, 2026
Summary: A framing calculator that turns wall length, stud spacing, openings, corners and tees into a stud count, plate lineal feet, headers and sheathing.

---

Log in (https://simplywise.com/login)

## Framing Calculator: Stud Count, Plates, and Cut List

Set the wall length, the spacing, and the openings. The stud count, plate lumber, headers, cripples, and sheathing sheets update as you type.

Add SimplyWise as a preferred source (https://www.google.com/preferences/source?q=simplywise.com)

Set the wall, get the stud count and the cut list

Stud spacing

Wall length (ft)

Wall height (ft)

Openings

Opening width (ft)

Corners

Partition tees Walls that tee in

32 studs to order

Field studs on layout16

King and jack studs4 kings, 4 jacks

Corner and tee studs8

Cripples above headers8

Headers2 at 4 ft

Plate lumber60 lineal ft

Wall sheathing5 sheets

One bottom plate and a double top plate, per IRC R602.3.2 and R602.3.4. Sheathing counts 4 by 8 panels at 32 sq ft. Code and panel sizes read September 11, 2026.

Wall length (ft)

Labor $ per foot of wall

Materials $ per foot of wall

$0 before markup

Labor$0

Materials$0

Defaults: a SimplyWise Cost Estimator run, October 13, 2026, framing a 20 ft, 8 ft tall wall: $600.00 labor, $273.83 materials.

At a glance

1. Field studs are floor(wall length in inches divided by spacing) plus 1.
2. Plates run three courses, per IRC R602.3.2 and R602.3.4.
3. Every opening adds two kings and two jacks, plus cripples to cut.
4. Each corner takes three studs, per AWC WFCM 3.4.1.1.3.
5. Each partition tee takes two studs, or ladder blocking.
6. Sheathing is wall area divided by 32 sq ft, rounded up.

## How the framing and stud calculator counts a wall

A framing calculator (or stud calculator) counts wall length over spacing plus one, then corner, tee and opening studs. Most stud counters stop at wall over spacing and miss the last bay, corners, tees and openings.

This framing calculator counts the layout, adds what openings and intersections need, and hands back a cut list. Layout studs inside an opening become cripples, listed on their own line.

## Framing calculator worked example: a 20 ft wall at 16 in

A 20 ft wall is 240 in. Divide by 16 for 15 bays, so the layout takes 16 field studs. Two openings at 4 ft add two kings and two jacks each: 4 kings and 4 jacks.

Two corners at three studs and one tee at two add 8 more, so the order is 32 studs. Plates are 20 ft times three courses, or 60 lineal feet.

Each 4 ft opening carries four cripples, 8 cripples in all. At 8 ft tall the wall is 160 sq ft, or 5 sheets of sheathing.

## The framing calculator cut list, piece by piece

| Piece | Count | Rule |
| --- | --- | --- |
| Field studs | 16 | floor(240 / 16) plus 1 |
| King studs | 4 | 2 per opening, full height |
| Jack studs | 4 | 2 per opening, cut to header height |
| Corner studs | 6 | 3 per corner, WFCM 3.4.1.1.3 |
| Tee studs | 2 | 2 per partition tee, backing allowance |
| Cripples | 8 | cut from layout studs over a header |
| Plates | 60 lineal ft | wall length times 3 courses |
| Sheathing | 5 sheets | 160 sq ft divided by 32, rounded up |

## Turn the cut list into a priced wall

SimplyWise Cost Estimator (https://www.simplywise.com/cost-estimator) turns a photo into an itemized estimate in about 6 seconds, with material and labor lines. Pricing is $29.99/mo or $239.99/yr, about $20/mo on annual, with a 7-day free trial.

## Stud size, height, and spacing the code allows

IRC Table R602.3(5) sets the limits. AWC publishes the same numbers in WFCM Table 3.20C.

| Stud | Loadbearing height | Roof and ceiling only | Roof, ceiling, one floor | Nonbearing height |
| --- | --- | --- | --- | --- |
| 2×4 | 10 ft | 24 in | 16 in | 14 ft at 24 in |
| 2×6 | 10 ft | 24 in | 24 in | 20 ft at 24 in |

24 in on center works on a 2×4 bearing wall only under a roof and ceiling. Add a floor and the table drops you to 16 in, or a 2×6.

## How many jack studs a header really needs

The framing calculator assumes one jack per end, which IRC Table R602.7(1) gives on short openings. Wider spans and heavier snow push that to two or three. These rows carry roof and ceiling only; a floor above cuts every span.

| Header | Snow load | Building width | Max span | Jacks per end |
| --- | --- | --- | --- | --- |
| 2 by 2×6 | 30 psf | 20 ft | 5 ft 5 in | 1 |
| 2 by 2×6 | 50 psf | 36 ft | 3 ft 8 in | 2 |
| 2 by 2×12 | 70 psf | 36 ft | 5 ft 10 in | 3 |

Check the span first: one jack where the table wants two fails in bearing.

## Lay out the wall without a recount

1. Pull layout from one end only Hook the tape on one end of both plates and mark every 16 in or 24 in across. Bay to bay measuring stacks errors until sheathing joints miss studs.
2. Mark the openings on the plates first Snap the rough openings on the bottom plate first. Kings sit outside, jacks inside, and the marks between them become cripples.
3. Count corners and tees separately A corner takes three studs and a tee takes two for backing. Ladder blocking does the same with scrap and leaves the bay open for insulation.
4. Order the plates as full lengths Order three courses at the wall length, with top plate splices 24 in from the joint below (R602.3.2).

## Keep reading

- Construction Calculators Hub (https://www.simplywise.com/blog/construction-calculators/)
- Drywall Sheet and Mud Calculator (https://www.simplywise.com/blog/drywall-sheet-and-mud-calculator/)
- Drywall Installation Cost (https://www.simplywise.com/blog/drywall-installation-cost/)
- Roof Replacement Cost (https://www.simplywise.com/blog/roof-replacement-cost/)
- Stair Calculator (https://www.simplywise.com/blog/stair-calculator/)

## Sources

### Code limits

- City of Seattle, Residential Code Chapter 6, Wall Construction (https://www.seattle.gov/documents/Departments/SDCI/Codes/SeattleResidentialCode/2015SRCChapter6.pdf) (Tables R602.3(5) and R602.7(1); R602.3.2; R602.3.4; verified 2026-09-11).

### Wood framing standards

- American Wood Council, Wood Frame Construction Manual 2018, Chapter 3 (https://awc.org/wp-content/uploads/2026/08/AWC_WFCM2018_20190430_website_chapter-3-prescriptive-design.pdf) (sections 3.4.1.1.3, 3.4.1.2, 3.4.1.3 and Table 3.20C; verified 2026-09-11).

### Panel sizes

- APA, Engineered Wood Construction Guide, Form E30T (panel dimensions, 4 by 8 ft; verified 2026-09-11).
- APA, Engineered Wood Construction Guide, Wall Construction excerpt, Form E30X (https://www.buildgp.com/wp-content/uploads/2022/06/2020-APA-Engineered-Wood-Construction-guide-Walls-E30.pdf) (sheathing thickness and span rating; verified 2026-09-11).

### Product

- SimplyWise Cost Estimator, App Store (https://apps.apple.com/us/app/simplywise-cost-estimator/id6670619664) (4.8 rating; verified 2026-09-09).

## Common questions about framing a wall

### Counting studs and plates

**How many studs are in a 20 ft wall at 16 in on center?**

16 field studs. Divide 240 in by 16 for 15 bays, then add 1 to close the last bay. Corners, tees, and openings add more.

**Why is the stud count one more than the wall divided by spacing?**

Because spacing counts bays, not studs. A wall with 15 bays has a stud on both sides of every bay, or 16 pieces.

**How much plate lumber does a wall take?**

Three times the wall length. R602.3.2 requires a double top plate and R602.3.4 a bottom plate, so a 20 ft wall runs 60 lineal feet.

### Openings, corners, and sheathing

**How many studs does an opening add?**

Two kings and two jacks, plus cripples above the header. At 16 in on center a 4 ft opening carries four cripples.

**How many studs go in a corner?**

Three. AWC Wood Frame Construction Manual 3.4.1.1.3 sets a minimum of three studs at each corner of an exterior wall.

**Can SimplyWise price the framing from a photo?**

Yes. SimplyWise Cost Estimator turns a photo into an itemized estimate in about 6 seconds, with material and labor lines. Free to try, at $29.99/mo or $239.99/yr.

Smart tools for contractors

- Log in (https://simplywise.com/login)
- New Business Program (https://www.simplywise.com/#program)
- About (https://www.simplywise.com/about)
- Support (https://www.simplywise.com/support)
- Privacy (https://www.simplywise.com/privacy)
- Terms (https://www.simplywise.com/terms)
- Blog (https://www.simplywise.com/blog/)

---

## About SimplyWise

SimplyWise, Inc. (New York, NY) builds mobile apps for contractors, tradespeople, and small business owners. The SimplyWise Cost Estimator turns a job site photo into an itemized estimate with labor and material costs in about 6 seconds, and the client signs the branded quote to approve it. It is rated 4.8 on the App Store. It is free to try with a 7-day free trial, then $29.99 per month or $239.99 per year (about $20 per month on the annual plan), and one subscription includes every app in the SimplyWise suite.

- Download: https://www.simplywise.com/download
- App Store: https://apps.apple.com/us/app/simplywise-cost-estimator/id6670619664
- Google Play: https://play.google.com/store/apps/details?id=com.simplywise.costestimator
- Every SimplyWise page as plain text: https://www.simplywise.com/blog/llms.txt